View and Download Laney LC30-II user manual online. LC30-II Amplifier pdf manual download. Also for: Lc50-ii. Laney Congratulations on your decision to purchase a Laney amplifier. Laney products are designed with ease of operation as a primary objective, however to ensure you derive the best from your new amplifier, it is important you take time to read this user manual and to familiarise yourself with the control functions and facilities available.
This little combo by Laney amplification is a good little multiple channel amplifier for someone who needs a small little combo that doesn't have a whole lot of wattage. This is a 30 W all tube amplifier that has a clean in overdrive channel. These amplifiers are made in the United Kingdom and have that typical British tone in the distortion channel. It's a very easy amplifier to dial in if you've ever had any experience with any type of British amplifier.UTILIZATIONThe look of this amplifier is not very intimidating at all. It only has a few controls that allow you to dial in a decent clean and decent overdrive tone.
You get a clean channel and an overdrive channel ans that is pretty much about it. There isn't that much to get in the way of your tone with added effects or modeling of any kind.SOUNDSIf you're into classic rock sound this this is going to be a good amplifier for you. If you are determined to get that British tone that you would get out of the Marshall or a Orange amp then this will be right up there with those tones. It's nothing to be ultra high gain and it's certainly not a fender clean amplifier. The clean is pretty decent and it sounds more like a Vox clean or a plexi clean.
The distortion channel is a mild break up very similar to eight Marshall at JCM 800 type tone. It's so it's going to get a little bit of dirt but not a very highly saturated tone.OVERALL OPINIONIs it fun little combo is if you can find him in the used market and they don't cost a whole lot. This is not the kind of amplifier that you really going to spend a lot of time trying to find because there's not really anything at this amplifier does a lot of other Marshall or Orange amplifier's can't do and do it a lot better. If you're struggling to find a simple amp then I suggest just don't waste anymore time and buy a nice little orange combo which has a much better distortion my opinion or a Marshall combo from the 80s. The new marshall combos aren't very good anymore so I suggest getting one from the 80s or just biting the and getting an orange amplifier combo.
Those orange amplifiers are very will built and have a solid tone all the way through each channel.
![Laney lc30 service manual Laney lc30 service manual](https://medias.audiofanzine.com/images/normal/laney-lc30-112-iii-2592076.jpg)
![Laney Laney](/uploads/1/2/5/5/125515296/864222725.jpg)
.BEFORE SWITCHING ON.SPECIFICATIONS Supply Voltage 100V, 120V, 230V, 240V 50/60Hz Factory Option Mains Fuse (220V240V = T630mA L 250V) (100120V = T1.6A L 250V) HT Fuse T315mA L Power Consumption 100W Output Power Rating Loudspeaker 12” Celestion 8 Ohms Loudspeaker outputs Extension speaker socket (Minimum 8 Ohm Impedance) Features Pure Class A Valve tone.INTRODUCTION.Your LC30-112 should give you years of trouble-free amplification, however please take time to read this manual and familiarise yourself with the controls as it will allow you to get the best from your amplifier. We hope you enjoy using your LC30-112 as much as we enjoyed designing and making it.FRONT PANEL CONTROLS HI INPUT: ‘Hi’ stands for high gain. This input is designed for the connection of low output level guitars making it well suited for guitars with single coiled or low gain humbucker type pickups. Use of high gain pickups in this input may drive the preamp too hard causing a 'mushy'.Switch in to enable the 'Drive' channel. (This switch must be in the disengaged position in order for the drive to be switched remotely via a foot switch.) DRIVE LED: This led will illuminate when the Drive channel is activated with the Drive switch (8) or an optional Laney FS2 remote footswitch. DRIVE: Sets the level of tube preamplifier drive or how dirty your sound is.REAR PANEL CONTROLS Spare power fuse included in the tray. L Z B 1 2 3 4 POWER INLET SOCKET: Connect to your power source.
Make sure the specified voltage is correct for your country! POWER FUSE: This drawer contains the main safety fuse for the unit.
The fuse protects the AC power to the amplifier. USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL.FX return signal sounds. This is an insert type control, therefore you need to set the Dry/ Wet mix in your FX processor. FOOTSWITCH SOCKET: Provided for the connection of a Laney FS2 footswitch (optional).This allows you to remotely switch between the clean/drive channel and & switch the built in reverb On/Off.QUICK START SETTINGS - suggestions only, experiment! CLEAN CLEAN CRUNCH BLUES LEAD ROCK LEAD Suggested starting point, adjust Tone to individual taste.USER SETTINGS - Store your own cool sounds. Tube amplifiers; generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes themselves. The LC30-112 uses top quality tubes, which should give you years of trouble free service, however like all tube amps; it is important to treat it with a certain amount of care.your loudspeakers.
Wait until all system parts have stabilised; usually a couple of seconds. Similarly when turning off your system always turn down the Volume controls on your guitar amplifier and then turn off its power before turning off other equipment.LC30-112 SAMPLE SYSTEMS FX Controller GS412A.NOTES.